Embedded Files
Site under construction by team of Gorillas untrained in graphic design, so please be patient.
---
Set Extruder to Absolute Mode
Set Extruder to Absolute Mode
M82
Instructs the printer to use absolute positioning for the extruder.
Instructs the printer to use absolute positioning for the extruder.
---
Set Extruder to Relative Mode
Set Extruder to Relative Mode
M83
Sets the extruder to relative positioning mode.
Sets the extruder to relative positioning mode.
---
Disable Steppers
Disable Steppers
M84
Turns off the motors (stepper drivers) after a period of inactivity or immediately when the command is issued.
Turns off the motors (stepper drivers) after a period of inactivity or immediately when the command is issued.
---
Set Steps per Unit
Set Steps per Unit
M92
Configures the number of steps the printer’s motors need to make per unit distance (used for calibration)
Configures the number of steps the printer’s motors need to make per unit distance (used for calibration)
---
Set Extruder Temp
Set Extruder Temp
M104
Sets the extruder target temp but doesn't wait for it to reach the temp before proceeding to the next line of code.
Sets the extruder target temp but doesn't wait for it to reach the temp before proceeding to the next line of code.
---
Set Extruder Temp and Wait
Set Extruder Temp and Wait
M109
Sets the extruder target temperature and pauses the print until the temp is reached.
Sets the extruder target temperature and pauses the print until the temp is reached.
---
Fan On
Fan On
M106
Controls the cooling fan, allowing you to set the fan speed (0-255 or a percentage).
Controls the cooling fan, allowing you to set the fan speed (0-255 or a percentage).
---
Fan Off
Fan Off
M107
Turns off the cooling fan
Turns off the cooling fan
---
Get Current Position
Get Current Position
M114
Reports the current position of the printer's axes.
Reports the current position of the printer's axes.
---
Display Message on LCD
Display Message on LCD
M117
Displays a custom message on the printer's LCD screen.
Displays a custom message on the printer's LCD screen.
---
Endstop Status
Endstop Status
M119
Returns the status of the printer's endstops (open/triggered).
Returns the status of the printer's endstops (open/triggered).
---
Set Bed Temp
Set Bed Temp
M140
Sets the heated bed target temperature but doesn't wait for it to reach the temp
Sets the heated bed target temperature but doesn't wait for it to reach the temp
---
Set Bed Temp and Wait
Set Bed Temp and Wait
M190
Sets the bed temperature and pauses the print until the bed reaches the target temp
Sets the bed temperature and pauses the print until the bed reaches the target temp
---
Play Tone
Play Tone
M300
Plays a beep or tone on the printer’s buzzer, typically with specified frequency and duration.
Plays a beep or tone on the printer’s buzzer, typically with specified frequency and duration.
---
Wait for Moves to Finish
Wait for Moves to Finish
M400
Ensures that all previously issued commands are completed before continuing to the next command
Ensures that all previously issued commands are completed before continuing to the next command
---
Save Settings to EEPROM
Save Settings to EEPROM
M500
Saves the current configuration settings to EEPROM so they persist across power cycles.
Saves the current configuration settings to EEPROM so they persist across power cycles.
---
Read Settings from EEPROM
Read Settings from EEPROM
M501
Loads previously saved settings from EEPROM.
Loads previously saved settings from EEPROM.
---
Revert to Default Settings
Revert to Default Settings
M502
Reverts the printer to factory or firmware-defined settings.
Reverts the printer to factory or firmware-defined settings.
---
Filament Change
Filament Change
M600
Initiates a filament change, often pausing the print and waiting for user intervention to load new filament
Initiates a filament change, often pausing the print and waiting for user intervention to load new filament
---
Restart after Error
Restart after Error
M999
Used to resume operation after a printer stop due to an error.
Used to resume operation after a printer stop due to an error.
Page updated
Google Sites
Report abuse